Per aggiornare FT2000 bisogna normalmente aprire la radio, svitare le viti del coperchio superiore ed inferiore, quindi raggiungere lo switch di programmazione S3004, togliendo inoltre le 15 viti del coperchio oppure raggiungendo lo switch S3004 attraverso il foro sul retro ma in modo piuttosto scomodo e pericoloso. Usate il vostro CAVO RS232 per il passaggio dei tati e al posto dello switch interno S3004 usate il DIN8 inserito come nelle spiegazioni. Velocissimi aggiornamenti. DIN/switch esterna per FT2000
* * * *
* * * *
PREGO LEGGERE IL NOSTRO "DISCLAIMER" PLEASE READ OUR "DISCLAIMER" INFO
FT-2000 owners. Bypass having to get at the S3004 switch in order to carry out a firmware upgrade you can use this special mini plug inserted into the FT2000 rear (external) socket. (The one with the foam insert) You just need to connect this wired plug, which does the same job as moving S3004 to ON. Just go through the routine as laid down but insert the din plug instead of opening up your FT-2000, or removing the back-right foot then with this plug, WITHOUT OPEN and without other wires!!! To use only your RS232 between radio and PC and our PLUG
External switch/wired special plug
Ihr könnt jetzt euren YAESU FT 2000 programmieren und neue firmware laden ohne transceiver öffnen!! Ihr solltet keine Zeit mehr verlieren, um euren FT 2000 zu öffnen um den switch S3004 zu finden. Wie mit dem CT119 könnt ihr leicht FT2000, mit diesem DIN8, einfach einstecken ohne ihn zu öffnen oder ihn rücken mit programmieren plug ohne other cable. Nur ein CAT RS232 zwischen RADIO und PC und unser DIN! Dann: AUSPACKEN EINSTECKEN FW LOSLEGEN !!!
* * * *
PROGRAMMARE IL VOSTRO FT2000 SENZA APRIRLO! L'originale YAESU CT119 consta in una comune COM MM 1:1 ed una presetta DIN da inserire nel retro del vostro FT2000 come spiegato sul manuale che lavora a livelli TTL, non abbiamo dettagli se questa poi resti isolata o altro ma il suo costo risulta sicuramente eccessivo.
VI PROPONIAMO UN SEMPLICISSIMO SWITCH ESTERNO PER AGGIORNARE IL VOSTRO FT2000 SENZA DOVERLO APRIRE Trattasi di una semplice presa DIN da inserire che ha la funzione del S3004 ma esterno!
FT2000 - SWITCH S3004 ESTERNO SEMPLICISSIMA E VELOCE PROCEDURA
-> Collegate la vostra normale seriale sulla COM tra PC<>RADIO
->
Spegnere il vostro FT2000 con l'interruttore frontale e quello sul retro
->
Programmare FT2000 come da specifiche firmware YAESU
->
Togliere la presetta DIN posteriore "simil CT119"
->
Quindi
usare FT2000 aggiornato!!!!
HOME MADE FIRMWARE SWITCH
FIRST GROUND THE DIN PIN 4 TO GND
1. INSERT DIN = LIKE SWITCH S3004 ON 2. REMOVE DIN = LIKE SWITCH S3004 OFF WITHOUT OPENING FT2000
** To look for from your electronic supplier "MINI DIN 8" **
=============================================================
=============================================================
=============================================================
EXTERNAL DIN PIN VIEW
=============================================================
INTERNAL DIN PIN VIEW
=============================================================
EXTERNAL FT2000 PIN VIEW
=============================================================
PIN VIEW THE nr 4 TO contour of metal of the DIN *** to simply connect the PIN4 with the metallic box of the DIN cover *** *** with a simple small switch to always hold DIN connected ***
=============================================================
WITH SIMPLE EXTERNAL SWITCH
THEN CONNECT YOUR RS232 CAT CABLE 1:1 F/F FROM PC to FT2000 AND GO TO UPDATE
ATTENTION: EDSP DOENSN'T USE THE DIN8 SWITCH THE EDSP PROCEDURE USE ONLY CAT RS232 1:1
BUONI ASCOLTI e BUONI DX CON YAESU FT2000! GOOD DX WITH YAESU FT2000
(c) 2007 - Come sempre non ci si ritiene responsabili per errori o malfunzionamenti dovuti a manipolazioni errate. Leggere il disclaimer pubblicato. Pleaseead the pubblied disclaimer. |